Loading...
Permits - Permit# SP-2021-00017 - 4238 West Arm Drive - 9/29/2021City of Spring Park Permit -} CITY OF ?� - To Schedule an Inspection Call: 952-442-7520 Details Permit Number: SP-2021-00017 Issue Date: 9/29/2021 Zoning Type: RESIDENTIAL Use Type: 24 HOUR NOTICE REQUIRED FOR ALL INSPECTIONS ♦ MON-FRI: 8AM-4:30PM • NO HOLIDAYS Site Address: 4238 WEST ARM DRIVE, SP, MN 55384 Description: Remove and Replace Existing Furnace Permit Granted To: Abel Heating and Cooling Homeowner's Name: MARILYN J BETHKE Phone Number: Parcel #: 1811723430177 Permit Type: MECH - Furnace (replacement) Permit Exp: 8/29/2021 Valuation: $3,400.00 Fees Receipt•• Date Quantity Date Paid Status Pmt Info Amount 13916 MECH - Fixture Maint 3/2/2021 1.00 9/29/2021 Paid American Express: *****"*-****3019 $50.00 13916 State Surcharge - Flat Fee $1.00 3/2/2021 1.00 9/29/2021 Paid American Express: **** ****-****3019 $1.00 Total: $51.00 Notes • This permit is issued in accordance with and subject to all provisions of Ordinances and policies governing building and zoning in City of Spring Park. • Permit Holder/Contractor/Owners Agent is responsible to call for the inspections! • Permit Packet, including approved plan, and this inspection record must be posted in an accessible location before calling for inspection. Maintain this inspection record until work is complete. • No deviations from the approved plans are allowed without prior consent from the building inspections department. • To Owner, Occupant, or Contractor: It is ILLEGAL TO OCCUPY this area/building until all required final inspections have been made, approved, signed, and certificate of occupancy issued! Scott Qualle, Building Official City of Spring Park 44349 Warren Avenue ♦ 55384 Copyright ©2021 INSPECTION RECORD 2020 MN State Building Code City of Spring Park Permit Number: SP-2021-00017 Issue Date: 9/29/2021 SITE ADDRESS: 4238 WEST ARM DRIVE, SP, MN 55384 Description: PERMIT TYPE: MECH - Furnace (replacement) Remove and Replace Existing Furnace ZONE/USE TYPE: RESIDENTIAL APPLICANT: Abel Heating and Cooling OWNER: MARILYN J BETHKE No inspection will be performed, and a re -inspection fee will be charged, if this "Inspection Record", the "City of Spring Park Permit", and, when applicable, the approved plans are not available to the inspector. This permit expires if construction activity does not commence within 180 days from obtaining this permit; when construction activity has been suspended or abandoned for at least 180 days; or the work has not been inspected within 180 days from the last documented activity. IF SEPARATE PERMITS ARE REQUIRED, REFER TO THE "SEPARATE PERMITS REQUIRED FOR:" STAMP ON YOUR APPROVED PLANS/CONSTRUCTION DOCUMENTS TO IDENTIFY WHAT SEPARATE PERMITS ARE REQUIRED. ALL REQUIRED ROUGH -IN INSPECTIONS, NOTED ON SEPARATE PERMITS, MUST BE COMPLETED PRIOR TO SCHEDULING A FRAMING INSPECTION. ALL REQUIRED FINAL INSPECTIONS, NOTED ON SEPARATE PERMITS, MUST BE COMPLETED PRIOR TO SCHEDULING A BUILDING FINAL INSPECTION. DO NOT COVER ITEMS TO BE INSPECTED. Permit Card Inspection Inspector's Response Approval Date Comments or Corrections RequireMechanical Final Required MUST CALL TO SCHEDULE NO LATER THAN THE BUSINESS DAY PRIOR TO THE INSPECTION DAY: 8:00 A.M. TO 4:30 P.M. MONDAY THRU FRIDAY. PHONE NUMBER TO CALL: 952-442-7520 When a Certificate of Occupancy is needed, return this card and the approved final inspection notice to the City of Spring Park office. CITY OF SPRING PARK PAGE 1 BUILDING PERMIT 4349 Warren Avenue 5 -:20a1- Ow13 Spring Park, MN 55384 ❑ Handout Given Routed t MNSPECT Phone: 952-471-9051 Fax: 952-471-9160 ❑ Lead Handout Given SITE ADDRESS' 4238 West Arm Drive PID: 1) Was the home constructed before 1978? (YES c, continue with line 2, NO o continue without completing EPA Section) 2) Will the work disturb 2:6 sq ft of interior painted surfaces or >_20 sq ft of exterior painted surfaces? (YES c go to line 4, NO$ine 3) 3) Are there any windows being replaced? (YES o, go to line 4, NO continue without completing EPA Section) • 4) Has this home been Certified Lead Free? (YES o, you MUST A ch Certification Information, Nq(u complete line 5) 5J EPA Contractor Certification Number NAT - (a piles to contractor only) • PROPERTY OWNER: Manlyn Bethke AddreSS 4238 West Arm Drive ' City: Spring Park State, MN Zip: 55384 Email: rs Contact Name Manlyn Bethke Phone: 952-334-9291 • CONTRACTOR: Abel Heating and Cooling Address: 6501 CO.Rd. 15 Minnetrista MN 55364 Cit : State: Zip: 952-472-2665 Phone: Fax: Contractor License No: MB003400 Contact Name: Mike Vaske Phone: 952-472-2665 Email: mvaske@abelonske.com ARCHITECT: Address: City State: Zip: Phone: Fax: • Email: Contact Name: Phone: TYPE OF WORK: E: New Construction o Deck Re -Roof o Commercial u_ Residential ❑ Change of Use ❑ Pool o Re -Side EST. VALUATION OF WORK , Finish Basement Retaining Wall c Fence $ 3400.00 o Remodel ❑ Porch D Shed Square feet -Addition o Demolition ❑ Window/Door Replacement c Garage-Attached/Detach ❑ Plumbing -provide detail on Page 2 # being replaced rr Detailed Description of Work: c Accessory Structure 2 Mechanical -provide detail on Page 2 ❑ Misc Other Furnace Replacement • Signature of this application by the legal properly owner or a licensed contractor. as ine owners representative.. is required and authorizes the Zoning Administrator or designee and the Building orfLoi or designee tc enter upon the property to perform needed inspections. Entry may be without prior notice. I hereby acknowledge that 1 have read this application and state that all information is true and coned to the oes: of my knowledge. I funher agree that aR work performed will be in accordance with approved plans specifications and cenddons and to abide by al ordinances of the Municpalrty and the lasts of the State of Minnesota regarding actions taken pursuant to this permit. I agree to pay all plan review fees even If I choose not to proceed with the work. Permit expires when work �s is not commenceo within 18o days from date of permit, or if work is suspended. abandoned. or no: inspected for 180 days. Work beyond the scope of this permit or soak without a permit or inspection. • will be subject to a penalty. Noise Ordinance In Effect: MONDAY - FRID Sef e 7 a.m. and after 10 p.m. Weekends/Holidays before 7 a.m. and after 8 p.m. SIGNATURE OF APPLICANT: DATE: 3lzl7 PRINTED NAME: Michael Vaske This is the signature of: _ Owner or z Owner's Representative OCCUP. TYPE: CONST. TYPE: CODE: BLDG SPRINKLED Yes/No VALUATION: $ Permit Fee: S WAC Charge: S Plan Review Fee: $ Sewer & Water Hook -Up: S State Surcharge: S Sewer & Water Disconnect S Site Inspection Fee: $ Water Meter. S S.E.C. Fee: S Muni SElWA Fee: S Investigation Fee / Other Fee: S '2016 SAC Escrow: $2 485 }' Copy Charge (S.25 per 8.5 x11 page) S Other S J ZO License Check ($5) / Lead Check ($5) S TOTAL DUE: $ �+� [ , C`Y' w SUB -TOTAL $ ,n Plumbing Fee (from Page 2) $ 'NOTE. Commercial plans will be submitted to the Met Council Environmental Svcs Z) 00 for SAC determination. Escrow payment will be required when permit is issued. If uJ Mechanical Fee from Page 2) 15[• after Met Council review no SAC Is determined, escrow will be refunded in full. U LL Special Conditions/Required Setbacks: LL O Building Approval By: DATE: Printed Building Approval By: C License Verification u Lead Verification - Checked By: City Approval DATE: 9 �� Paid 5'1 QE Date: Receipt No. LtI 63 By: CITY OF SPRING PARK MECHANICAL PERMIT ❑ PLUMBING PERMIT PAGE 2 FOR PERMIT ISSUANCE PAGE 1 and PAGE 2 should be complete _MECHANICAL INFORMATION Mechanical Contractor: Abel Heating and Cooling Address: 6501 CoAd. 15 c Minnetdsta State: MN Zip: 55364 Phone: 952-472-2665 Fax: State Bond No: MB003400 Contact Name: Mike Vaske Email: mvaske abelonsite.com Contact Phone: 952-472-2665 Detailed Description of Work: Remove and replace existing fumace. Indicate type of project, fixtures, and Gas Lines you will be installing MECHANICAL FIXTURES or replacing (include count for each type of fixture): GAS LINES Quantity Quantity uantit 1 Furnace Kitchen Fan Air Conditioning System Bath Fan Furnace Fireplace Air Exchanger Grill Unit Heater Fireplace Water Heater Unit Heater Grill In Floor Heat Dryer Gas Log Stove 0 Replacement (one fixture only: no piping or vent changes) Office Use Only: Mechanical Permit Fee: $ 50• Cb ❑ Addition/Remodel ❑ New Construction Gas Line Permit Fee: $ State Surcharge: $yd c Other Other: $ Total Mechanical Permit: $ PLUMBING INFORMATION Plumbing Contractor: Address: City: State: Zip: Phone: Fax: Plumbers License No: State Bond No: Contact Name: Contact Phone: Email - Detailed Description of Work: Indicate type of project and fixtures you will be installing or replacing (include count for each type of fixture): PLUMBING FIXTURES Quantity Quantity Quantity Water Heater Shower Laundry Tub Gas = Electric Dishwasher Rough -In Future Fixture Water Softener Clothes Washer Sump Lawn Sprinkler System Ice Maker Line Water Piping System Water Closet (Toilet) Hose Bib Floor Drain Lavatory Wash Basin Bathtub Office Use Only: ❑ Replacement (one fixture only, no piping or vent changes) Plumbing Permit Fee: $ o Addition/Remodel State Surcharge $ ❑ New Construction Other: $ o Other Total Plumbing Permit: $ Thank you for your Payment! Transaction ID: 13916 Transaction Number: 14163329 Transaction Type: Payment Recipient: Contractor Notes: Fees l cf ry oa "'VA r � 'K 0r City of Spring Park 4349 Warren Avenue SP MN,55384 Ph:952-442-7520 $51.00 Date: 9/29/2021 Method: American Express: ****-**** ****3019 Address: 4238 WEST ARM DRIVE, SP, MN 55384 Reference: Permit Number: SP-2021-00017 Type: MECI (replacement) for Abel Heating and Cooling MECH - Fixture Maint Paid 1.00 $50.00 $50.00 State Surcharge - Flat Fee $1.00 Paid 1.00 $1.00 $1.00 Total Amount: $51.00 Page 1 of 1 Printed on: 9/29/2021 Payment Confirmation Payer Information: Payment Made By: Leah Knapp-Ridler Payment Made For: Abel Heating and Cooling Email: mvaske@abelonsite.com Permit Address: 4238 West Arm Drive Address: 6501 Co. Rd. 15 Minnetrista, MN 55364 Payment Description: Permits Payment Date: 9/29/2021 3:08:53 PM Payment Payment Confirmation Convenience Business Name Method Account Number Amount Fee Total City of Spring Park AMEX ****3019 14163329 $51.00 $2.25 $53.25 (Permits) This notice confirms that the above payment was successfully submitted to our payment processor, PSN, and is currently being processed. Thank you for using PSN. NOTE: While credit and debit cards generally are immediately approved, the transaction is not considered "paid" until the credit or debit card company has "settled" the payment which occurs most often within 24 hours. If there are any issues with your payment, PSN will send an email to the address you provided. To check on the progress of your payment, you can log into your profile. Thanks for using PSN. Contact Us PSN Customer Support Submit your question and get a response within one business day. Payment Processing Powered by Payment Service Network (PSN) THIS COMMUNICATION IS INTENDED ONLY FOR THE ADDRESSEE(S) AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED AND CONFIDENTIAL. YOU ARE HEREBY NOTIFIED THAT, IF YOU ARE NOT AN INTENDED RECIPIENT LISTED ABOVE, OR AN AUTHORIZED EMPLOYEE, OR AGENT OF AN ADDRESSEE OF THIS COMMUNICATION RESPONSIBLE FOR DELIVERING E-MAIL MESSAGES TO AN INTENDED RECIPIENT, ANY DISSEMINATION, DISTRIBUTION, OR REPRODUCTION OF THIS COMMUNICATION (INCLUDING ANY ATTACHMENTS HERETO) IS STRICTLY PROHIBITED. IF YOU HAVE RECEIVED THIS COMMUNICATION IN ERROR, PLEASE NOTIFY US IMMEDIATELY BY A REPLY E-MAIL ADDRESSED TO THE SENDER AND PERMANENTLY DELETE THE ORIGINAL E-MAIL COMMUNICATION AND ANY ATTACHMENTS FROM ALL STORAGE DEVICES WITHOUT MAKING OR OTHERWISE RETAINING A COPY. �� j w w w ,SPEC Phone: -442-7 21 t )/ ' �/"v LLc Fax: 952-442-7521 Email: info@mnspect.com HELPING YOU COMPLY WITH RESIDENTIAL MECHANICAL AND FIREPLACE HANDOUT ➢ This handout is intended only as a guide. It shall not be considered a complete set of requirements. ➢ Materials and installation must comply with the current Minnesota State Mechanical and Fuel Gas Codes, and the manufacturers' installation specifications for each product. ➢ A new or replacement appliance requires a mechanical permit if a new or reconfigured gas line and/or new or reconfigured venting is required. Examples of appliances include: furnaces, boilers, cooling equipment (portable or window units excluded), geothermal equipment, fireplace units (non -masonry only, masonry fireplaces require a building permit), water heaters, in -floor heat, air exchangers, unit heaters and dryers, kitchen and bathroom exhaust vents. The installation, replacement or reconfiguration of a gas line also requires a mechanical permit. ➢ Multiple appliances may be included on the same mechanical permit, provided that they will be ready for inspection at the same time. Residential mechanical permits can be issued over the counter at the municipality office. Commercial projects require a plan review. Please request a Commercial Mechanical Permit Application from your municipality office. ➢ The following items do NOT need a mechanical permit UNLESS there is a gas line or venting involved as described above: Microwaves, electric stoves, refrigerators, freezers, space heaters, electric dryers, or countertop appliances. (Note: if the appliance is to be hard -wired an electrical permit is required.) (This is not an exhaustive list — for questions about whether a permit is required, call 952-442-7520. ➢ The manufacturer's installation and specification manual must be available at all inspections. Exhaust vent clearances at the exterior of the structure shall be in compliance with manufacturer's specifications. '(throughoutproject)be: POSTED prior to start of work - VISIBLE from street or driveway - ACCESSIBLE to the inspector INSPECTION REQUIREMENTS: Inspections MUST be scheduled during office hours AT LEAST one business day prior to inspection. If a specific date and time is required, additional notice may be needed. Failure to cancel a scheduled inspection may result in a reinspection fee. o Office Hours: Monday - Friday • 8:00 a.m. - 4:30 p.m. o Phone: (952) 442-7520 or (888) 446-1801 inspections (required inspections are dependent on the project type): o Someone 18 years or older must be present at the time of the inspection. o Mechanical rough -in: After all the supply/return air ducts and bath/kitchen fans and vents are installed (if applicable). No work shall be covered until the rough -in inspection is approved. The manufacturer's installation instructions MUST be on site at the rough -in inspection. (NO rough -in inspection is required for projects such as a furnace or air conditioner replacement.) o Gas Line Air Test: A gas line air test is required on all newly installed gas lines when all the gas lines are installed, gas lines are capped off, and the air test is on the system line. ✓ Test pressure shall be no less than one and one-half times the proposed maximum working pressure, but not less than 25 psi irrespective of design pressure. ✓ Test pressure shall be within the middle 50% of the test gauge pressure range, marked in 2 psi increments. ✓ Test duration shall not be less than 30 minutes for residential gas lines. o Mechanical final: After all mechanical equipment is installed; supply/retum air grilles are operational and running; HRV or ERV is balanced; the bath/kitchen exhaust fan(s) are operational; and all intake and exhaust piping is complete. Manufacturer's installation instructions MUST be on site. For all new or replacement gas -fired furnaces and boilers, a completed Certification of Testing of Fuel Gas -Fired Heating Equipment (ORSAT) is required (attached). Test results must meet the minimum requirements of Chapter 9 of the current MN Fuel Gas Code. Test results shall be provided to the inspector and posted on the appliance at the time of the final inspection. Residential Mechanical/Fireplace Handout Page 1 of 6 Copyright @ MNSPECT 2020, Rev. July 2020 o Gas line/fitting leak test: A gas line fitting/leak test is required on all newly installed gas lines after all work is complete. You may perform a leak test on site at the time of the final inspection, or provide a completed Certification of Final Testing on Gas Line and Fittings form (attached) at the time of the final inspection. The test shall be by means of an approved combustible gas detector, manometer, a noncorrosive leak detection fluid, or an equivalent nonflammable solution. NOTICE: Construction or work for which a permit is required shall be subject to inspection by the Building Official, and such construction or work shall remain accessible and exposed for inspection purposes until approved. It is the responsibility of the permit applicant to be in attendance on site and provide access to the Building Official for all required inspections. If work is concealed and/or work is not complete at time of inspection, an additional inspection is required and a reinspection fee may apply. Note: The State of Minnesota requires all residential building contractors, remodelers, roofers, plumbers, and electricians to obtain a state license, unless they qualify for a specific exemption. Any person claiming an exemption must provide a copy of a Certificate of Exemption from the Department of Labor & Industry to the Municipality before a permit will be issued. Note: To determine contractor requirements, or to check the licensing status of a contractor, please call the Minnesota Department of Labor & Industry at 651-284-5065 or toll free 1-800-342-5354. Note: For specific code requirements, contact the Building Inspection Department at 952-442-7520 or 888-446-1801 or e-mail: info6�pmnspect.com. PROJECT CHECKLIST: The following is a guideline to assist in compliance with the requirements of the MN State Building Code. BATHROOMS: ❑ The required bathroom ventilation rate for toilet, shower/bath, and similar rooms is 50 cubic feet per minute (cfm) intermittent or 20 cfm continuous. Bathroom ventilation requirements can also be met by installing an operable window, in which case the minimum openable area to the outdoors shall be a minimum of 1.5 sf. BATH FANS: ❑ Ducting material must be an approved material. Flexible duct is allowed, but must be listed and labeled class 0 or class 1 duct that is tested in accordance with UL 181. ❑ Termination of exhaust ducting must be at least 3' from openings into the building (such as non - mechanical air intakes, windows and doors). ❑ Exhaust fans must discharge outdoors. Termination must be equipped with a backdraft damper. (This is in addition to the damper at the fan.) Air must not be exhausted into the attic or crawl space. ❑ Insulation with a thermal resistance of R-3.3 and a vapor retarder with all joints sealed is required 3' back from the exterior wall/roof sheathing on exhaust ducting inside conditioned space, and continuous in attics/unconditioned space. Insulation and vapor retarder are required from the exterior wall or roof sheathing to 3 feet in to a conditioned space. In unconditioned spaces, the insulation and vapor barrier shall be continuous and extend to a conditioned space. The insulation shall be a minimum of R-3.3 and the vapor barrier shall have lapped and taped seams. VENTILATION OF UNINHABITED SPACE: ❑ Conditioned crawl spaces require mechanical ventilation of .02 cfm per square foot or a minimum 1 supply and 1 return duct. This ventilation may be provided by a supply duct or a mechanical fan and humidistat. Supply and return must be separated by one half of the diagonal room dimension. ❑ Unconditioned crawl spaces shall be ventilated per Section 408 of the Minnesota Residential Code. DRYER VENT: (MN Mechanical Code 913, 504.4) ❑ Exhaust vents for clothes dryers shall be constructed of metal and have a smooth interior finish. ❑ The duct shall be a minimum size of 4". ❑ The maximum length shall not exceed 35' with a deduction of 5' for each 90-degree elbow (may use specific requirements provided by dryer manufacturer). ❑ No screws or rivets that penetrate more than 1/8" into the duct may be used to secure the duct. Dryer duct must be secured in place; joints are to be sealed with tape or other approved material found in MMC 603.9. Tape should be marked 181 B-FX. ❑ Each vertical riser shall be provided with a means for cleanout. ❑ Male ends of joints shall extend in the direction of airflow. ❑ Transition ducts may be used to connect the appliance but must not be concealed or exceed 8' in length, and must be tested and labeled in accordance with UL 2158A. Residential Mechanical/Fireplace Handout Page 2 of 6 Copyright © MNSPECT 2020, Rev. July 2020 ❑ At the time of the rough -in inspection, the appliance must be set and vented; in addition, framing, draft, and fire stopping must be installed and accessible. The rough -in inspection is required prior to installation of drywall or plywood. GAS PIPING: ❑ Gas piping to the appliance should be installed and visible at the time of the rough -in inspection of the fireplace. ❑ Gas piping must be of approved materials and installation methods. ❑ Corrugated Stainless Steel Tubing (CSST) installations must follow manufacturer's installation instructions for the specific brand of CSST installed. ❑ CSST installations require a qualified installer. (Certification is available to homeowners.) ❑ CSST installation also requires bonding as detailed in the specific manufacturer's installation instructions. ❑ A 25# air pressure test is required on all newly installed gas lines before final connection to the house gas distribution system. This can be achieved by closing gas valves and/or capping and isolating the line from the house gas supply and the appliance regulator. (Under no circumstances should pressure be applied to the appliance regulator or the house distribution system.) ❑ At the final inspection all finish materials must be installed including mantel and surrounds, the gas line connected, and all applicable related electrical inspected and approved (if applicable). The manufacturer's installation instructions must be available at the final inspection. Residential Mechanical/Fireplace Handout Page 4 of 6 Copyright © MNSPECT 2020, Rev. July 2020 Certification of Final Testing on Gas Line and Fittings (This form must be completed and provided to the inspector at final inspection of all newly installed gas lines and/or fittings.) PERMIT NUMBER: Site Address: Municipality: Company/Installer Name: Date of Work Completion: Describe the Scope of Work Performed Be specific — include what work was performed, the appliance being serviced, what new components were installed (i.e. gas line, fittings, shut-off valves), and the type of material (i.e. black iron, copper, corrugated stainless steel, plastic). Attach additional sheet(s) if needed: Type of Approved Test Performed: I certify that on the above -stated approved test was completed in (Date) accordance with Section 406 of the MN Fuel Gas Code, that all work was completed prior to the test, and that no leaks were detected upon completion of the test. (Signature of Certifying Individual) (Printed Name) Residential Mechanical/Fireplace Handout Page 5 of 6 (Certification Date) Copyright © MNSPECT 2020, Rev. July 2020 Certification of Testing of Fuel Gas -Fired Heating Equipment (This form must be completed and provided to the inspector at final inspection of all gas -fired furnaces and boilers.) PERMIT NUMBER: Site Address: Municipality: Company/Installer Name: Date of Test Completion: ORSAT Test Results Atmospheric Induced Draft/Fan- Assisted Power Type Item Code Reg. Actual Code Reg. Actual Code Reg. Actual Efficiency >_ 75 % >_ 75 % z 80 % CO level <- .04% <- .04% <- .04% Stack Temp <_ 4800 F <_ 4800 F <_ 4800 F + ambient OR <_ 125' F in excess of fluid Temp + ambient CO2 level Between 6- 9% Between 6-9% Between 6-9% Oxygen level Between 4-10% Between 4-10% Between 3-10% I certify that on the above -stated approved test was completed in (Date) accordance with Section 1346.5900 of the MN Fuel Gas Code, that all work was completed prior to the test and that the fuel gas -fired equipment meets the performance standards for the type of equipment. A copy of the test results along with the installer's name and test date must be affixed to the appliance. (Signature of Certifying Individual) (Certification Date) (Printed Name) Residential Mechanical/Fireplace Handout Page 6 of 6 Copyright © MNSPECT 2020, Rev. July 2020 520 l M N S P E TLLC FAO 952-44.2- 5271 HELPING YOU COMPLY V TA;�� ,,,;nth EMAIL: INFOPMNSPECT.COM NOTICE This notice is to be given to the homeowner The improvements undertaken at this property require the inspection of properly installed smoke alarms and carbon monoxide alarms, as required by MN Statute 299F.362, 299R.51, and in accordance with NFPA 72 and MN Residential Code (MRC) R314 & R315. This notice is intended to inform the homeowner of the requirements at the beginning of the project in an effort to minimize any inconvenience and/or cost associated with an additional inspection if the work described in this handout is not completed before the final inspection. The guidelines below are to assist you in completing the require installation. For questions please call MNSPECT at 952-442-7520 or 888-446-1801. REQUIREMENTS FOR SMOKE & CARBON MONOXIDE ALARMS ➢ This handout is intended only as a guide. It shall not be considered a complete set of requirements. ➢ Materials and installation must comply with the current Minnesota State Building Code and the manufacturers' installation specifications for each product. SMOKE ALARMS: Smoke alarms are required: • MN Statue 299R.662 requires smoke alarms installed in every residential dwelling in Minnesota. Each dwelling until must be provided with UL 217 listed smoke alarms installed in accordance with NFPA 72 and MRC 314. (Combination smoke and carbon monoxide alarms are permitted in lieu of smoke alarms and must be listed UL 217 and UL 2034.) Smoke alarms must be installed: • In each sleeping room. • Outside AND within the immediate vicinity (within 21' per NFPA 72) of each separate sleeping area. • On each additional story of the dwelling including basements and habitable attics. Installation requirements: • Smoke alarms shall be installed not less than 3' horizontally from the door or opening of a bathroom that contains a shower or tub unless this would conflict with other placement requirements such as minimum distance from a bedroom. • Ionizing alarms shall not be installed closer than 20' to a cooking appliance. Ionization alarms with a silencing switch may be placed no closer than 10' to a cooking appliance. • Photoelectric alarms shall not be installed closer than 6' to a cooking appliance. • Wall mounted alarms should be located inside an area not more than 12" and not less than 4" from the ceiling (or per the manufacturer's requirements). • Ceiling mounted alarms should be no closer than 4" from a side wall or peak of a vaulted ceiling. Smoke and CO Alarms Handout Page 1 of 2 Copyright © MNSPECT 2020, Rev. April 2020 • Alarms must be more than 36" from the tip of a ceiling fan blade, forced air supply register, or door to a bathroom that contains a tub or shower. • Smoke alarms shall not be installed within a 36-inch horizontal path from the supply registers of a forced air heating or cooling system and shall be installed outside of the direct airflow from those registers. • Alarms should be mounted on an interior wall. • Alarms should be mounted away from windows and exterior doors. Interconnection: • Where more than one alarm is required to be installed, the devices shall be interconnected either by physical interconnection, or by a wireless interconnection. Exception: Interconnection is not required in existing areas where the alterations or repairs do not involve the removal of interior ceiling or wall finishes exposing the structure. Power Source: • Smoke alarms shall receive their primary power from the building wiring & shall have a battery backup. Exception: o Battery operated alarms shall be permitted in buildings without commercial power. o Alarms in existing areas shall be permitted to be battery operated when the alterations or repairs do not involve the removal of the interior ceiling or wall finishes exposing the structure. ➢ Smoke alarms should be replaced every 10 years (or per manufacturer's instructions). ➢ Smoke alarm batteries should be changed every year. CARBON MONOXIDE ALARMS: Carbon monoxide (CO) is a silent killer. It is a poisonous, colorless, odorless, and tasteless gas produced by burning gasoline, wood, propane, charcoal, or other fuel. Improperly ventilated appliances and engines may allow carbon monoxide to accumulate to dangerous levels. Large amounts of CO can overcome you in minutes without warning. Carbon monoxide alarms are required: • MN Statue 299R.51 & MRC R315 require carbon monoxide alarms to be installed in every residential dwelling that: o Contains a fuel -fired appliance, and/or o Has an attached garage that communicates with the dwelling unit. Carbon monoxide alarms shall be listed UL 2034. (Combination smoke and carbon monoxide alarms are permitted and must be listed UL 217 and UL 2034.) Carbon monoxide alarms must be installed: • Outside and within 10' of every sleeping room. • On each level containing a sleeping room. • Inside each sleeping room where that room or an attached bathroom contains a fuel -fired appliance. Interconnection: Where more than one alarm is required to be installed, the devices shall be interconnected either by physical interconnection, or by a wireless interconnection. Exception: Interconnection is not required in existing areas where the alterations or repairs do not involve the removal of interior ceiling or wall finishes exposing the structure. Power Source: • CO alarms shall receive their primary power from the building wiring & shall have a battery backup. Exception: o Battery operated alarms shall be permitted in buildings without commercial power. o Alarms in existing areas shall be permitted to be battery operated when the alterations or repairs do not involve the removal of the interior ceiling or wall finishes exposing the structure. ➢ Carbon Monoxide alarms should be replaced every 6 years (or per manufacturer's instructions). ➢ CO alarm batteries should be changed every 6 months. Smoke and CO Alarms Handout Page 2 of 2 Copyright © MNSPECT 2020, Rev. April 2020