Permits - Permit# 22SP-00042, 00043, 00044 - 4490 West Arm Road - 11/5/2022 City of Spring Park Repair/Remodel/Alteration
(Residential)
4349 Warren Ave, Spring Park, MN 55384
PRING PARK 22SP-00042
rn Lae Ninneton a (952)471-9051 (952)471-9160
For Inspections: (952) 442-7520
Date Issued: 11/05/2022 Property Owner: MARK A& SARAH G REINHARDT
Expiration Date: 05/04/2023 Mailing Address: 4490 WEST ARM RD
Job Site Address: 4490 WEST ARM ROAD, SPRING
PARK, MN 55384 SPRING PARK, MN 55384
Category: Residential Alteration Phone:
Permit Type: Repair/Remodel/Alteration Email:
(Residential)
Valuation: $2,200.00
Description of Work:
LAUNDRY ROOM REMODEL
Subdivision: Required Setbacks:
Parcel ID: 1811723340067
Filing:
Lot: 10 Actual Setbacks:
Block:
Total Sq Ft:
Contractors: Fee Items Amount
State Surcharge $ 1.10
Residential Building Permit $ 120.25
Residential Plan Review $78.16
Total Fees: $ 199.51
NOTICE
Signature of Applicant/Date Building Department Signature/Date
11/05/2022
MUST BE POSTED ON JOB SITE
INSPECTION CARD
4i�' City of Spring Park
SPRING PARK
On Lakf Ninnetonkp 4349 Warren Ave, Spring Park, MN 55384
POST THIS CARD IN A SAFE CONSPICUOUS LOCATION.PLEASE DO NOT REMOVE THIS NOTICE UNTIL ALL REQUIRED INSPECTIONS ARE MADE AND SIGNED OFF BY THE APPROPRIATE
AUTHORITY AND THE BUILDING IS APPROVED FOR OCCUPANCY.STAMPED APPROVED PLANS MUST BE AVAILABLE ON THE JOBSITE.
Repair/Remodel/Alte
PERMIT NO.: 22SP-00042 PERMIT TYPE: ration(Residential) ISSUED DATE: 11/05/2022 EXPIRATION DATE: 05/04/2023
1811723340
PROJECTADDRESS: 4490 WEST ARM ROAD,SPRING PARK,MN 55384 PARCEL NO.: 067
OWNER: MARK A&SARAH G REINHARDT CONTRACTOR: CONTRACTOR PHONE:
DESCRIPTION OF WORK: LAUNDRY ROOM REMODEL
CONSTRUCTION TYPE: OCCUPANT LOAD:
DATE DATE
INSPECTION INSP PASSED COMMENTS INSPECTION INSP PASSED COMMENTS
Framing Energy Code/Insulation
Building Final
Fire Approval: Date: Engineering Date:
Approval:
PW Approval: Date: Other( ): Date:
To request an inspection:(952)442-7520
Paae 1 of 1
City of Spring Park Gas Line Only (Residential)
4349 Warren Ave, Spring Park, MN 55384
PRING PARK 22SP-00043
La a Yinneton a (952)471-9051 (952)471-9160
For Inspections: (952) 442-7520
Date Issued: 11/05/2022 Property Owner: MARK A& SARAH G REINHARDT
Expiration Date: 05/04/2023 Mailing Address: 4490 WEST ARM RD
Job Site Address: 4490 WEST ARM ROAD, SPRING
PARK, MN 55384 SPRING PARK, MN 55384
Category: Residential Miscellaneous Phone:
Permit Type: Gas Line Only(Residential) Email:
Valuation:
Description of Work:
LAUNDRY ROOM REMODEL
Subdivision: Required Setbacks:
Parcel ID: 1811723340067
Filing:
Lot: 10 Actual Setbacks:
Block:
Total Sq Ft:
Contractors: Fee Items Amount
State Surcharge(Fixed) $ 1.00
Residential Gas Line Only Permit $ 50.00
Total Fees: $51.00
NOTICE
Signature of Applicant/Date Building Department Signature/Date
11/05/2022
MUST BE POSTED ON JOB SITE
INSPECTION CARD
*Jiul City of Spring Park
SPRING PARK
On Lake511tinnetonka 4349 Warren Ave, Spring Park, MN 55384
POST THIS CARD IN A SAFE CONSPICUOUS LOCATION.PLEASE DO NOT REMOVE THIS NOTICE UNTIL ALL REQUIRED INSPECTIONS ARE MADE AND SIGNED OFF BY THE APPROPRIATE
AUTHORITY AND THE BUILDING IS APPROVED FOR OCCUPANCY.STAMPED APPROVED PLANS MUST BE AVAILABLE ON THE JOBSITE.
Gas Line Only
PERMIT NO.: 22SP-00043 PERMIT TYPE: (Residential) ISSUED DATE: 11/05/2022 EXPIRATION DATE: 05/04/2023
1811723340
PROJECT ADDRESS: 4490 WEST ARM ROAD,SPRING PARK,MN 55384 PARCEL NO.: 067
OWNER: MARK A&SARAH G REINHARDT CONTRACTOR: CONTRACTOR PHONE:
DESCRIPTION OF WORK: LAUNDRY ROOM REMODEL
CONSTRUCTION TYPE: OCCUPANT LOAD:
DATE DATE
INSPECTION INSP PASSED COMMENTS INSPECTION INSP PASSED COMMENTS
Mechanical Rough-In Air/Hydrostatic Test
Reports Mechanical Final
Fire Approval: Date: Engineering Date:
Approval:
PW Approval: Date: Other( ): Date:
To request an inspection:(952)442-7520
Paae 1 of 1
City of Spring Park Plumbing (Residential)
4349 Warren Ave, Spring Park, MN 55384
O MMG PARK 22SP-00044
La a Alinneton a (952)471-9051 (952)471-9160
For Inspections: (952) 442-7520
Date Issued: 11/05/2022 Property Owner: MARK A& SARAH G REINHARDT
Expiration Date: 05/04/2023 Mailing Address: 4490 WEST ARM RD
Job Site Address: 4490 WEST ARM ROAD, SPRING
PARK, MN 55384 SPRING PARK, MN 55384
Category: Residential Miscellaneous Phone:
Permit Type: Plumbing (Residential) Email:
Valuation:
Description of Work:
LAUNDRY ROOM REMODEL
Subdivision: Required Setbacks:
Parcel ID: 1811723340067
Filing:
Lot: 10 Actual Setbacks:
Block:
Total Sq Ft:
Contractors: Fee Items Amount
State Surcharge(Fixed) $ 1.00
Residential Plumbing Permit $75.00
Total Fees: $76.00
NOTICE
Signature of Applicant/Date Building Department Signature/Date
11/05/2022
MUST BE POSTED ON JOB SITE
INSPECTION CARD
City of Spring Paris
SPRING PARK
On Lake91finnefonka 4349 Warren Ave, Spring Park, MN 55384
POST THIS CARD IN A SAFE CONSPICUOUS LOCATION.PLEASE DO NOT REMOVE THIS NOTICE UNTIL ALL REQUIRED INSPECTIONS ARE MADE AND SIGNED OFF BY THE APPROPRIATE
AUTHORITY AND THE BUILDING IS APPROVED FOR OCCUPANCY.STAMPED APPROVED PLANS MUST BE AVAILABLE ON THE JOBSITE.
Plumbing
PERMIT NO.: 22SP-00044 PERMIT TYPE: (Residential) ISSUED DATE: 11/05/2022 EXPIRATION DATE: 05/04/2023
1811723340
PROJECT ADDRESS: 4490 WEST ARM ROAD,SPRING PARK,MN 55384 PARCEL NO.: 067
OWNER: MARK A&SARAH G REINHARDT CONTRACTOR: CONTRACTOR PHONE:
DESCRIPTION OF WORK: LAUNDRY ROOM REMODEL
CONSTRUCTION TYPE: OCCUPANT LOAD:
DATE DATE
INSPECTION INSP PASSED COMMENTS INSPECTION INSP PASSED COMMENTS
Underground Plumbing Plumbing Rough-In
Plumbing Final
Fire Approval: Date: Engineering Date:
Approval:
PW Approval: Date: Other( ): Date:
To request an inspection:(952)442-7520
Paae 1 of 1
CITY OF SPRING PARK PAGE 1 BUILDING PERMIT
4349 Warren Avenue 22SP-00042
Spring Park, MN 55384 ❑ Handout Given ad
Phone: 952-471-9051 Fax: 952-471-9160 ❑ Lead Handout Given
31TE ADDRESS:_-/4 4 o V ) 6r ate PID: -3�}-
1)Was the home constructed before 1978'?(YES a,continue with line 2.NOXcontinue without completing EPA Section)
Will the work disturb 2:6 sq ft of interior painted surfaces or>_2G sq ft of exterior painted surfaces?(YES❑go to line 4,NOX-6ine 3)
I)Are there any windows being replaced?(YES n,go to line 4 NoXccontinue without completing EPA Section)
4)Has this home been Certified Lead Free?(YES,i you MUST Attach Certification Information NO u complete fine 5)
5)EPA Contractor Certification Nurater. NAT- (applies to contractor only)
s PROPERTY OWNER: ,L kia t 6-d f Aodress 4 qQ W iAiQ
a : f-i nQ Pa zate: M N zip; 9 4 Email: re-r'n ba rd '/.
f untact Name
-_ Phone q5"I— a D
CONTRACTOR: #n m P t5Q Address:
City: State: Zi . Phone: Fax-
Contractor License No: Contact Name: 4-nc
Email_
ARCHITECT: Address: T s
city: State: Zip: Phone: F"_
Emaii: Coniact NarTW Phone:
TYPE OF WORK: New Co is ructuc-ri Decmh w Pool - ^Re-p"of
Commerr;,al _ Znh*1,1e,*Use Rvts'n"t,;L,:a:: .. Forcr, Re-Side
EST VALUA'hONOF WORK Fxrish Basement r;iiior �er•ce
S -G7�T�t ar �dtl 9rg Sol lr:k.a- Sheo _
Square feet n Z 7.Addit,un F-io a;a-n )�Andam,:Doo,Rtplauernent
fa TV, -Gal aje-Attachc-1/Dsta:h "-uOg-;ro•,dedeta �
on Paget #being reulad �—
r, Detailed Description of Work A�cesst:�j�n:c±tfre— Mmt,echanical,ro4'de-+eta::c-rage^ Mist;Other
.See ah�drh
spnatjre of ih` apt c bn b leas'Propel_ow a c Scar s_•C ce,cute as S:? x rE y:se ntaC.e, trey,,ed er.atr f o,;zes the Zc r g Adrr:r';La c,a Ges' se and the Eh •ftng oN:_`.sl
,^-des:gneetoer'_r��c•ti:apr.:,xrt,bpeYo.�;nec.q. ._Y.:Norsfr-._..a Su:•�rc. I...ra'_'�.Ihen�,ack.c•.�:ge..�tl;a�ecead_isrpp._ah'o•tar3s;ate'tat:::arfi-•:a;,:-:stn,a��
:orett to the best Of r;r r isege.i hrt:xr ay e•+'h9t e:•,y isr'�C i.,eN.: _matt`, to s appr--.-r't 3.aps.p',:s,7:,r•'..anG.,io%]nu tv:it ye by a ex-ia•tces b:the:r:r:•:�';
•d r w:.:.:a of uit Sla,e t:1A'r,ar.�e:r;r.4•t i•:-•a ta'?.ti.r:,�.:•tc` : .v'a..r agree to pay all plan review reaa sven tr i choose not to proceed wah the wof%,Pe:rr.'.e-
u 9113tce-re":atv.'rr ,.£1•!8yyh:.+•.'Y�ap•�:..•� .r5'.• :•A'x;rnc:aC.a'•�n.:-nw� ur::i •±�a^tad.' tPJd,_.YfcXbe,�nd..es:3peoil' s7an.i•or•--jort•,t:.,oui-Pemaa:nspectim.
.v.'be s'.'c y tc a Prna._.
Noise Ordinar:`e 1n Effect 140NDAY-FRIDAY Before 7 a.m.and after 10 p.m.Weekands/Holidays before 7 a.m.and after 8 p.m.
SIGNATURE OF APPLICANT. e4/� � Y DATE:
PRINTED NA.'JE: ry Triis is the signature of: ),hr,eror � Owner's Rwescrit tiva
OCCUP.T.-F :I RC-1 CONST.TYPE: N/A CODE_2020 MR(; BLDG SPRINKLED Ye !No
VALUATION.$2-712.24 nn C
Permit Fee: w OT J WAG Charge: $
Plan Rrview Fee: $ Sew_r&Water Hook-Up: $
State Surcharge: $�� . 1 l"� Sewer&Water Diswnnet;t $
Site Inspeztion Fee: $ Water Meter. $
S_E.C.Fee: $ Muni SE'WA Fee: $
Investigation Fee/Other Fee: $ SAC Escrow.$2485
J Copy Charge($?5 per 8.5 x 11 page) $ Other. $
O License Chock($5)/Load Check($5) $ TOTAL DUE; $
W SUB-TOTAL $
in Commercial plans will be submitted to the Met Council Environmental Svcs
Plumbing Fee(from Page 2) $ for SAC determination. Escrow payment will be required when permit is issued. if
W Mechanical Fee(from Page 2) $ after Met Council review,no SAC is determined,escrow will be refunded in full.
U
U. Special Conditions/Required Setbacks:
O
Building Approval Bv:2)&= z,z 7y DATE: 10/31/2022
Printed Building Approval By: Derrick Wyman ❑ License Verification ❑ Lead Verification-Checked By:D 2U
City Approval By: DATE:
Paid: Date: Receipt No. By:
CITY OF SPRING PARK MECHANICAL PERMIT
ALUMBING PERMIT
PAGE 2 FOR PERMIT ISSUANCE
PAGE i and PAGE 2 should be complete
MECHANICAL INFORMATION
Mechanical Contractor: tfjj7De Qj3n,07 Address:
City: State: zip: Phone: Fax:
State Bond No: I Contact Name:
Email: lContact Phone:
Detailed Descri Lion of Work:
see
Indicate type of project,fixtures,and Gas Lines you will be installing or replacing(include count for each type Of,fixture):
MECHANICAL FIXTURES GAS LINES
Quantity Quantity Quad
Furnace Kitchen Fan Furnace
Air Condition'.ng System Bath Fan Fireplace
Air Exchanger G,ill Un?t Heater ^r
Fireplace Water HWiv'
Unit Heater Grill n �,J ~
In Floor Halat !dryer ��(t'[f�i�J tf vn.pve �Gt 5 Cart err
Gas LogSio:p
llrk-e Use Or=y.r
Replacement(one fixts re only,no pip ng or vent OA, nges) r ti,achanicai Perms Fee.
Addition!Remndei Gas Line Permit Fee: $
New Construction State Surcharge:
Other Other. $_
Total Mechanical Permit: $
PLUMBING INFORIVIA-1710N
Plumbing Contractor: 7 7n-7 e taTi)f Address:
Citi': State: Zip. Phone: Fax:
Plumbers License No: State Bond No:
Contact Name: lContact Phone:
Email: _
Detailed Descrl tlon of Work:
Ind;x:ate type of project and fixtures you will be installing or replacing (include count for each type of fixture):
PLUMBING FIXTURES
Quaritilty Quantftycant'
Water Heater Shovtar Laundry Tub
- Gas r Electric Dishwasher Rough-In Future F+xtu.-e
Water Softener ��Clothes Washer Sump
Lawn 5prinkier System Ice Maker'Line Water Pipinq System
Water Closet(Toilet) Hose Bib Floor Drain
Lavatory Wash Basin Bathtub
Office Use Only:
Replacement(one fixture only, no piping or vent changes) Plumbing Permit Fee: $
a Addition/Remodel State Surcharge $
❑ New Construction Other: $
a Other Total Plumbing Permit: $
SPRING PARK
On Luke Ytinnetonka
October 31, 2022
Permit Number: 22SP-00042
Project Name: Mark and Sarah Reinhardt
4490 West Arm Road
Spring Park, MN 55384
Scope: Residential Code Review of a laundry room remodel, involving re-locating washing
machine, and installing stackable washer and dryer unit with the dryer changing from gas,
to existing electrical service, in a single-family home.
Inspections: All work shall be inspected. It is the responsibility of the contractor/installer to contact the
Department of Building Safety, when ready to schedule an inspection, at 952-442-7520
between the hours of 8:00 a.m. and 4:30 p.m., Monday through Friday.
The plans and specifications for the project named above have been reviewed for substantial compliance
with the current Minnesota State Building Code. The review is limited to the submitted scope of work
and is based upon the supposition that the data on which the design is based are correct, and that the
necessary legal authority has been obtained to construct the project. The responsibility for the design of
structural features must be taken by the project designer. Any changes from the submitted plans and
specifications shall be reviewed and approved by the Department of Building Safety.
Approval is based on the correction of all noted deficiencies and compliance with all applicable
items listed below.
The following information is related to the submitted plans/scope as general information and/or code
compliance requirements. Compliance with the stated requirements shall be verified during the
construction process. Any changes to the plan and any required additional information shall be provided
to this agency for code-compliance review and approval, prior to its installation.
General Information:
1. Applicable Codes:
a. 2020 MN Residential Code (MRC) (2018 IBC as amended)
b. 2015 MN Energy Code (MREC) (2012 IECC as amended)
c. 2020 MN Mechanical Code (MMC) (2018 IMC as amended)
d. 2020 MN Fuel Gas Code (MFGC) (2018 IFGC as amended)
e. 2015 MN State Plumbing Code (MPC) (2012 UPC as amended)
f. 2020 MN Electrical Code (MEC) (NFPA 70)
2. Separate permits are required for:
a. Mechanical
b. Plumbing
3. The field inspector may identify additional code compliance requirements. Any additional
identified code compliance requirements shall be completed.
Specific Code Items to Be Addressed During Construction:
1. Specific plan items that need to be addressed
The below items are commonly missed items that require correction following inspections.
These are provided for your benefit and may or may not apply specifically to your project. Items
or sections new to the 2020 Code are Italicized.
MN Residential Code:
1. Habitable space, hallways, bathrooms, toilet rooms, laundry rooms, and portions of basements
containing these spaces shall have a ceiling height of not less than 7 feet. The required height
shall be measured from the finished floor to the lowest projection from the ceiling. (MRC
R305.1)
a. Exception: Bathrooms shall have a minimum ceiling height of 6 feet 8 inches at the
center of the front clearance area for water closets, bidets, or sinks. The ceiling height
above fixtures shall be such that the fixture is capable of being used for its intended
purpose. A shower or tub equipped with a shower head shall have a minimum ceiling
height of 6 feet 8 inches above a minimum area 30 inches by 30 inches at the
showerhead.
2. Smoke alarms shall be installed in the following locations: (MRC R314.3)
a. In each sleeping room.
b. Outside each separate sleeping area in the immediate vicinity of the bedrooms.
c. On each additional story of the dwelling, including basements and habitable attics but
not including crawl spaces and uninhabitable attics. In dwellings or dwelling units with
split levels and without an intervening door between the adjacent levels, a smoke alarm
installed on the upper level shall suffice for the adjacent lower level provided that the
lower level is less than one full story below the upper level.
3. Smoke alarms shall not be installed in the following locations unless it would prevent another
required placement: (MRC R314.3.1)
a. Ionization smoke alarms shall not be installed less than 20'from cooking appliance
b. Ionization smoke alarms with a silencing switch shall not be installed less than 10'from a
cooking appliance
c. Photoelectric smoke alarms shall not be installed less than 6'from a cooking appliance.
d. Smoke alarms shall not be installed within 3'horizontally of a bathroom that contains a
tub or shower.
4. Smoke alarms shall be interconnected. Wireless units that meet UL 217 may be used in lieu of
hardwire interconnection. Combination alarms shall be listed in accordance with UL 217 and
UL 2034. (MRC R314.4)
5. Carbon monoxide alarms shall be installed outside and not more than 10 feet (3048 mm) from
each separate sleeping area or bedroom. Alarms shall be installed on each level containing
sleeping areas or bedrooms. Alarms shall also be installed inside each bedroom where a fuel-
fired appliance is present in the bedroom or it's attached bathroom. (MRC R315.3)
6. CO alarms shall be interconnected. Wireless units that meet UL 2034 may be used in lieu of
hardwire interconnection. Combination alarms shall be listed in accordance with UL 217 and
UL 2034. (MRC R314.4)
7. CO alarms shall receive their primary power from the building wiring where such wiring is
serviced from a commercial source, and where the power is interrupted, shall receive power
from a battery. (MRC R315.6)
MN Energy Code:
1. All exhaust, supply, and return air ducts and plenums shall be insulation according to Table
R403.2.1. (MREC R403.2.1)
a. Insulation is only required in the conditioned space for a distance of 3 feet from the exterior
or unconditioned space.
b. V means the vapor retarder in accordance with IMC Section 604.11
c. W means an approved weatherproof barrier.
TABLE R403.2.1 MINIMUM REQUIRED DUCT AND PLENUM INSULATION
Duct Type/Location Duct Type/Location
Exterior of building R-8, V and W
Attics, garages, and ventilated R-8 and V
crawls aces
Exhaust ducts within conditioned R3.3 and V
spaces
2. Ducts, air handlers, and filter boxes shall be sealed. (MREC R403.2.2)
3. Building framing cavities shall not be used as ducts or plenums. (MREC R403.2.3)
4. Insulation for new hot water pipe with a minimum thermal resistance (R-value) of R-3 shall be
applied to the following:
a. Piping larger than 3/4-inch nominal diameter.
b. Piping from the water heater to kitchen outlets.
c. Piping located outside the conditioned space.
d. Piping from the water heater to a distribution manifold.
e. Piping located under a floor slab.
f. Buried piping.
g. Supply and return piping in recirculation systems other than demand recirculation
systems.
h. Piping with run lengths greater than the maximum run lengths for the nominal pipe
diameter given in Table R403.4.2.
All remaining piping shall be insulated to at least R-3 or meet the run length requirements of Table
R403.4.2.
TABLE R403.4.2 MAXIMUM RUN LENGTH feet
Nominal Pipe Diameter of Largest 3/8 1/2 3/4 > 3/4
Diameter Pipe in the Run inch
Maximum Run Length 30 120 1 10 5
5. A minimum of 75 percent of the lamps in permanently installed lighting fixtures shall be high-
efficacy lamps or a minimum of 75 percent of the permanently installed lighting fixtures shall
contain only high efficacy lamps. (MREC R404.1)
Mechanical Code Items:
1. Mechanical ventilation requires a minimum exhaust rate of 50 cfm in toilet rooms and bathrooms.
(MMC 403.2.1)
2. The air removed by every mechanical exhaust system shall be discharged outdoors at a point
where it will not cause a nuisance and not less than the distances specified in IMC Section
501.3.1. The air shall be discharged to a location from which it cannot again be readily drawn in
by a ventilating system. Air shall not be exhausted into an attic or crawl space and the exhaust
system shall be equipped with a backdraft damper at the point of discharge. (MMC 501.3)
3. The termination points of exhaust outlets and ducts discharging to the outdoors shall be located
with the following minimum distances (MMC 501.3.1)
a. For all environmental air exhaust: 3 feet from property lines; 3 feet from operable openings
into buildings, and 10 feet from mechanical air intakes.
MN Fuel Gas Code:
1. Corrugated stainless steel tubing (CSST) gas piping systems shall be bonded to the electrical
service grounding electrode system. The bonding jumper shall connect to a metallic pipe or fitting
between the point of delivery and the first downstream CSST fitting. The bonding jumper shall be
not smaller than 6 AWG copper wire or equivalent. Gas piping systems that contain one or more
segments of CSST shall be bonded in accordance with this section. (MFC 310.1.1)
2. Corrugated stainless steel tubing (CSST) that is not listed with an arc-resistant jacket or coating
system in accordance with ANSI LC 1/CSA 6.26. CSST gas piping systems and piping systems
containing one or more segments of CSST shall be electrically continuous and bonded to the
electrical service grounding electrode system or, where provided, the lightning protection grounding
electrode system. (MFC 310.2)
3. The bonding jumper shall connect to a metallic pipe, pipe fitting or CSST fitting. (MFC 310.2.2)
4. The bonding jumper shall be not smaller than 6 AWG copper wire or equivalent. (MFC 310.2.3)
5. The length of the bonding jumper between the connection to a gas piping system and the
connection to a grounding electrode system shall not exceed 75 feet(22 860 mm). Any additional
grounding electrodes installed to meet this requirement shall be bonded to the electrical service
grounding electrode system or, where provided, the lightning protection grounding electrode
system. (MFC 310.2.3)
6. Bonding connections shall be in accordance with NFPA 70. 310.2.5 Connection devices. Devices
used for making the bonding connections shall be listed for the application in accordance with UL
467. (MFC 310.2.4)
7. This section applies to corrugated stainless-steel tubing (CSST) that is listed with an arc-resistant
jacket or coating system in accordance with ANSI LC 1/CSA 6.26. The CSST shall be electrically
continuous and bonded to an effective ground fault current path. Where any CSST component of a
piping system does not have an arc-resistant jacket or coating system, the bonding requirements of
Section 310.2 shall apply. Arc-resistant-jacketed CSST shall be considered to be bonded where it is
connected to an appliance that is connected to the appliance grounding conductor of the circuit that
supplies that appliance. (MFC 310.3)
8. Where in contact with or passing through concrete or other abrasive material, metallic piping and
fittings coated with a corrosion-resistant material, sleeve, or casing shall be used. Steel pipe
exposed in exterior locations shall be galvanized or coated with approved corrosion-resistant
material. (MFC 403.8)
9. Prior to acceptance and initial operation, all piping installations shall be visually inspected and
pressure tested to determine that the materials, design, fabrication and installation practices comply
with the requirements of this code. (MFC 406.1)
b. Test Pressure. Test pressure shall be measured with a manometer or with a pressure-measuring
device designed and calibrated to read, record, or indicate a pressure loss caused by leakage
during the pressure test period. The source of pressure shall be isolated before the pressure tests
are made. Mechanical gauges used to measure test pressures shall have a range such that the
highest end of the scale is not greater than five times the test pressure.
c. Test pressure. The test pressure to be used shall be no less than one and one-half times the
proposed maximum working pressure, but not less than 25 psig irrespective of design pressure.
d. Test Duration. Test duration shall be not less than one-half hour. When testing a system in a
single-family dwelling, the test duration shall be permitted to be reduced to 10 minutes with prior
approval from the building official.
e. Test gauges. Tests which utilize dial gauges shall be performed with gauges of 2 psi
incrementation or less and shall have a pressure range not greater than twice the test pressure
applied. The test pressure shall be within the middle 50 percent of the test gauge pressure range.
10. Piping systems shall be provided with an approved main shutoff valve before the first branch line.
The main shutoff valve shall be installed in the first available location inside the building 5 feet or
less above the floor that provides ready access and shall have a permanently attached handle.
(MFC 409.1.4)
11. Piping shall be supported at intervals not exceeding the spacing specified in Table 415.1. Spacing
of supports for CSST shall be in accordance with the CSST manufacturer's instructions.
TABLE 415.1 SUPPORT OF PIPING
STEEL PIPE, NOMINAL SIZE OF
NOMINAL SIZESPACING OF TUBING SPACING OF
OF PIPE SUPPORTS (SMOOTH-WALL) SUPPORTS
inches feet inch O.D. feet
'/2 6 112
/4 or 1 8 1/8 or 3/4 6
11/4 or larger 10 7/8 or 1 8
horizontal horizontal
11/4 or larger Every floor 1 or larger Every floor
vertical level vertical level
Plumbing Code Items:
1. Domestic dishwashers shall discharge through an air gap fitting in accordance with 807.4 into a
waste receptor, a wye branch fitting on the tailpiece of a kitchen sink or dishwasher connection
on a food waste grinder. (MPC 414.3)
If you have any questions or concerns regarding this plan review please contact me via telephone at
952-442-7520 or email at codereview(a mnspect.com.
Derrick Vyman
Code Official
MNSPECT, LLC., A SAFEbuilt Company
Helping You Comply With The Code
235 First St. W.
Waconia, MN 55367
Office: 952-442-7520
www.mnspect.com
CC: City Property File
Read all attached materials.
Buildings shall have approved address
Everyone performing work numbers, building numbers or approved
to which the code is building identification placed in a position
applicable shall comply with that is plainly legible and visible from the
the code. street or road fronting the property. These
numbers shall contrast with their
background. Addresses shall be Arabic
The field copy of these plans must be numbers or alphabetical letters. Numbers
kept on-site and made available to shall not be spelled out. Each character
inspector during all inspections. shall be a minimum of 4 inches high with a
To schedule inspections call minimum stroke width of 1/2 inch. Where
(952) 442-7520 access is by means of a private road and
the building cannot be viewed from the
Please have the permit number and public way, a monument, pole or other sign
street address ready at the time of the or means of identification shall be used and
call. maintained.
Plan Revisions
All construction shall comply with the Electrical
approved plans.
All electrical must be approved by local Electrical
Plan revisions will not be reviewed in Inspector.
the field without prior approval from the For electrical permit inquiries please contact the City of
Building Official. Submit all plan Spring Park Electrical Inspector.
revisions to the Department of Building Dave Hucky
Safety for review, prior to their (952) 442-7520
construction.
Reviewed for Code Compliance Separate Permits
p Required For:
This review is limited to the submitted scope of work, is based upon the supposition that the plan Electrical
accurately depicts the intended construction and end-use, that the necessary legal authority has
been obtained to construct the project and work is subject to code compliance and field �' Mechanical
inspection during construction. /T Plumbing
By: Derrick Wyman Type of Construction: Not Applicable Fireplace
Demolition
Date: 10/31/2022 Occupancy Classification: IRC-1 Single Family Fire Suppression System
Septic
Permit #: 22SP-00042 Code Edition: 2020 MN Residentail Code
October 26, 2022
Reinhardt - 4490 W Arm Rd
Laundry/Mud Room Project Description:
Plumbing
1. Move existing front load washer 5ft. Move plumbing, include adding water
connection valves on wall and new drain pipe
2. Remove existing laundry tub/faucet and replace with new sink/faucet and
cabinet.
Mechanical
3. Remove existing Gas Dryer and replace with stacking front load Electric Dryer.
Electric outlet (240v) and 30A circuit are already available.
Building
4. Stacking Washer and Dryer will be surrounded by cabinet (see attached drawing)
5. Other cabinets will also be installed. (see attached drawing)
6. Replace existing door from laundry/mudroom to attached garage with pre-hung
steel exterior door.
Estimated Valuation
Door: $600
Dryer: $1000
Sink/faucet. $500
Additional Plumbing parts: $100
TOTAL: $2200
Cabinet cost not included in Est. Valuation
sbuwl!au 148 :sty-gz-ogz (G913) t4lev"5
x p x-a;-3 UJOUH LLJ008 /UP]—Intl 1PIV14UIRL
010 0 0
00 0
A A
*4:P
00- 0
00
Cl
bt bIL-
Alls
.4 E
ANOJA POUXOOAO
UIOOH pf)VT&tPlmvl 1pjul4uh9H
RECEIPT
City of Spring Park
4349 Warren Ave, Spring Park, MN 55384
(952)471-9051
SPRING PARK
22SP-00042 i Repair/Remodel/Alteration (Residential) On Lake W innetonka
Receipt Number:83
Payment Amount: $199.51 November 5,2022
Transaction Method Payer Cashier Reference Number
Credit Card Sarah Reinhardt Jamie Hoffman 52510311
Comments
Assessed Fee Items
Fee items being paid by this payment
Date Fee Item Account Code Assessed Amount Paid Balance Due
10/27/22 State Surcharge $1.10 $1.10 $0.00
10/27/22 Residential Building Permit $120.25 $120.25 $0.00
10/27/22 Residential Plan Review $78.16 $78.16 $0.00
Totals: $199.51 $199.51
Previous Payments $0.00
Remaining Balance Due $0.00
Permit Info
Property Address Property Owner Property Owner Address Valuation
4490 WEST ARM ROAD MARK A& SARAH G 4490 WEST ARM RD $2,200.00
SPRING PARK, MN 55384 REINHARDT SPRING PARK, MN 55384
Description of Work
LAUNDRY ROOM REMODEL
Payment Confirmation
Payer Information:
Payment Made By: Sarah Reinhardt
Payment Made For: Sarah Reinhardt
Email: sgreinhardt@hotmail.com
Permit Address: 4490 W Arm Rd
Address: 4490 W Arm Rd
Spring Park, MN 55384
Payment Description: Permits
Payment Date: 11/3/2022 1:03:41 PM
Business Name Payment Payment Confirmation Convenience
Method Account Number Amount Fee Total
City of Spring Park AMEX ****1017 52510311 $326.51 $9.63 $336.14
(Permits)
This notice confirms that the above payment was successfully submitted to our payment processor, PSN,
and is currently being processed. Thank you for using PSN.
NOTE: While credit and debit cards generally are immediately approved, the transaction is not considered
"paid" until the credit or debit card company has "settled"the payment which occurs most often within 24
hours. If there are any issues with your payment, PSN will send an email to the address you provided. To
check on the progress of your payment, you can log into your profile. Thanks for using PSN.
Contact Us
PSN Customer Support Submit your question and get a response within one business day.
Payment Processing Powered by Payment Service Network (PSN)
THIS COMMUNICATION IS INTENDED ONLY FOR THE ADDRESSEE(S)AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED AND CONFIDENTIAL.
YOU ARE HEREBY NOTIFIED THAT, IF YOU ARE NOT AN INTENDED RECIPIENT LISTED ABOVE,OR AN AUTHORIZED EMPLOYEE,OR AGENT OF AN
ADDRESSEE OF THIS COMMUNICATION RESPONSIBLE FOR DELIVERING E-MAIL MESSAGES TO AN INTENDED RECIPIENT,ANY DISSEMINATION,
DISTRIBUTION,OR REPRODUCTION OF THIS COMMUNICATION(INCLUDING ANY ATTACHMENTS HERETO)IS STRICTLY PROHIBITED.IF YOU HAVE
RECEIVED THIS COMMUNICATION IN ERROR,PLEASE NOTIFY US IMMEDIATELY BY A REPLY E-MAIL ADDRESSED TO THE SENDER AND
PERMANENTLY DELETE THE ORIGINAL E-MAIL COMMUNICATION AND ANY ATTACHMENTS FROM ALL STORAGE DEVICES WITHOUT MAKING OR
OTHERWISE RETAINING A COPY.
RECEIPT
City of Spring Park �^
4349 Warren Ave, Spring Park, MN 55384
(952)471-9051
SPRING PARK
22SP-00043 i Gas Line Only(Residential) On Lake.3finnetonka
Receipt Number:84
Payment Amount: $51.00 November 5,2022
Transaction Method Payer Cashier Reference Number
Credit Card Sarah Reinhardt Jamie Hoffman 52510311
Comments
Assessed Fee Items
Fee items being paid by this payment
Date Fee Item Account Code Assessed Amount Paid Balance Due
11/01/22 State Surcharge(Fixed) $1.00 $1.00 $0.00
11/01/22 Residential Gas Line Only Permit $50.00 $50.00 $0.00
Totals. $51.00 $51.00
Previous Payments $0.00
Remaining Balance Due $0.00
Permit Info
Property Address Property Owner Property Owner Address Valuation
4490 WEST ARM ROAD MARK A& SARAH G 4490 WEST ARM RD
SPRING PARK, MN 55384 REINHARDT SPRING PARK, MN 55384
Description of Work
LAUNDRY ROOM REMODEL
Payment Confirmation
Payer Information:
Payment Made By: Sarah Reinhardt
Payment Made For: Sarah Reinhardt
Email: sgreinhardt@hotmail.com
Permit Address: 4490 W Arm Rd
Address: 4490 W Arm Rd
Spring Park, MN 55384
Payment Description: Permits
Payment Date: 11/3/2022 1:03:41 PM
Business Name Payment Payment Confirmation Amount Convenience Total
Method Account Number Fee
City of Spring Park AMEX ****1017 52510311 $326.51 $9.63 $336.14
(Permits)
This notice confirms that the above payment was successfully submitted to our payment processor, PSN,
and is currently being processed. Thank you for using PSN.
NOTE: While credit and debit cards generally are immediately approved, the transaction is not considered
"paid"until the credit or debit card company has"settled"the payment which occurs most often within 24
hours. If there are any issues with your payment, PSN will send an email to the address you provided. To
check on the progress of your payment, you can log into your profile. Thanks for using PSN.
Contact Us
PSN Customer Support Submit your question and get a response within one business day.
Payment Processing Powered by Payment Service Network (PSN)
THIS COMMUNICATION IS INTENDED ONLY FOR THE ADDRESSEE(S)AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED AND CONFIDENTIAL.
YOU ARE HEREBY NOTIFIED THAT,IF YOU ARE NOT AN INTENDED RECIPIENT LISTED ABOVE,OR AN AUTHORIZED EMPLOYEE,OR AGENT OF AN
ADDRESSEE OF THIS COMMUNICATION RESPONSIBLE FOR DELIVERING E-MAIL MESSAGES TO AN INTENDED RECIPIENT,ANY DISSEMINATION,
DISTRIBUTION,OR REPRODUCTION OF THIS COMMUNICATION(INCLUDING ANY ATTACHMENTS HERETO)IS STRICTLY PROHIBITED.IF YOU HAVE
RECEIVED THIS COMMUNICATION IN ERROR,PLEASE NOTIFY US IMMEDIATELY BY A REPLY E-MAIL ADDRESSED TO THE SENDER AND
PERMANENTLY DELETE THE ORIGINAL E-MAIL COMMUNICATION AND ANY ATTACHMENTS FROM ALL STORAGE DEVICES WITHOUT MAKING OR
OTHERWISE RETAINING A COPY.
RECEIPT
City of Spring Park •i^
4349 Warren Ave, Spring Park, MN 55384
(952)471-9051
SPRING PARK
22SP-00044 I Plumbing (Residential) On LabeWinnetonka
Receipt Number: 85
Payment Amount: $76.00 November 5,2022
Transaction Method Payer Cashier Reference Number
Credit Card Sarah Reinhardt Jamie Hoffman 52510311
Comments
Assessed Fee Items
Fee items being paid by this payment
Date Fee Item Account Code Assessed Amount Paid Balance Due
11/01/22 State Surcharge(Fixed) $1.00 $1.00 $0.00
11/01/22 Residential Plumbing Permit $75.00 $75.00 $0.00
Totals. $76.00 $76.00
Previous Payments $0.00
Remaining Balance Due $0.00
Permit Info
Property Address Property Owner Property Owner Address Valuation
4490 WEST ARM ROAD MARK A& SARAH G 4490 WEST ARM RD
SPRING PARK, MN 55384 REINHARDT SPRING PARK, MN 55384
Description of Work
LAUNDRY ROOM REMODEL
Payment Confirmation
Payer Information:
Payment Made By: Sarah Reinhardt
Payment Made For: Sarah Reinhardt
Email: sgreinhardt@hotmail.com
Permit Address: 4490 W Arm Rd
Address: 4490 W Arm Rd
Spring Park, MN 55384
Payment Description: Permits
Payment Date: 11/3/2022 1:03:41 PM
Business Name Payment Payment Confirmation Convenience
Method Account Number Amount Fee Total
City of Spring Park AMEX ****1017 52510311 $326.51 $9.63 $336.14
(Permits)
This notice confirms that the above payment was successfully submitted to our payment processor, PSN,
and is currently being processed. Thank you for using PSN.
NOTE: While credit and debit cards generally are immediately approved, the transaction is not considered
"paid" until the credit or debit card company has"settled"the payment which occurs most often within 24
hours. If there are any issues with your payment, PSN will send an email to the address you provided. To
check on the progress of your payment, you can log into your profile. Thanks for using PSN.
Contact Us
PSN Customer Support Submit your question and get a response within one business day.
Payment Processing Powered by Payment Service Network (PSN)
THIS COMMUNICATION IS INTENDED ONLY FOR THE ADDRESSEE(S)AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED AND CONFIDENTIAL.
YOU ARE HEREBY NOTIFIED THAT,IF YOU ARE NOT AN INTENDED RECIPIENT LISTED ABOVE,OR AN AUTHORIZED EMPLOYEE,OR AGENT OF AN
ADDRESSEE OF THIS COMMUNICATION RESPONSIBLE FOR DELIVERING E-MAIL MESSAGES TO AN INTENDED RECIPIENT,ANY DISSEMINATION,
DISTRIBUTION,OR REPRODUCTION OF THIS COMMUNICATION(INCLUDING ANY ATTACHMENTS HERETO)IS STRICTLY PROHIBITED.IF YOU HAVE
RECEIVED THIS COMMUNICATION IN ERROR,PLEASE NOTIFY US IMMEDIATELY BY A REPLY E-MAIL ADDRESSED TO THE SENDER AND
PERMANENTLY DELETE THE ORIGINAL E-MAIL COMMUNICATION AND ANY ATTACHMENTS FROM ALL STORAGE DEVICES WITHOUT MAKING OR
OTHERWISE RETAINING A COPY.