Loading...
Permits - Permit# 25SP-00049 - 3842 Sunset Drive - 7/24/2025PARK City of Spring Park Repair/Remodel/Alteration (Residential) 4349 Warren Ave, Spring Park, MN 55384 Phone:(952) 471-9051 Fax: (952) 471-9160 For Inspections: (952) 442-7520 25SP-00049 Date Issued: 07/24/2025 Property Owner: DAVID D LU & MARY M LU Expiration Date: 01/20/2026 Mailing Address: 5555 MATTERHORN DRIVE NE Job Site Address: 3842 SUNSET DR, SPRING PARK, MN 55384 FRIDLEY, MN 55432 Category: Residential Alteration Phone: (763) 586-1012 Permit Type: Repair/Remodel/Alteration Email: ddtotmn@gmail.com (Residential) Valuation: $5,695.00 Description of Work: re -locate one closet wall in one bedroom. re -locate one bathroom wall in the bedroom. relocate vanity. Subdivision: Required Setbacks: Parcel ID: 17-117-23-32-0012 Filing: Actual Setbacks: Lot: Block: Total Sq Ft: Contractors: Fee Items Amount State Surcharge $ 2.85 Residential Building Permit $ 173.50 Residential Plan Review $ 112.78 Total Fees: $ 289.13 NOTICE Signature of Applicant/Date Building Department Signature/Date 07/24/2025 MUST BE POSTED ON JOB SITE INSPECTION CARD City of Spring Park SPRING PARK On Lake %innetonka 4349 Warren Ave, Spring Park, MN 55384 POST THIS CARD IN A SAFE CONSPICUOUS LOCATION. PLEASE DO NOT REMOVE THIS NOTICE UNTIL ALL REQUIRED INSPECTIONS ARE MADE AND SIGNED OFF BY THE APPROPRIATE AUTHORITY AND THE BUILDING IS APPROVED FOR OCCUPANCY. STAMPED APPROVED PLANS MUST BE AVAILABLE ON THE JOBSITE. Repair/Remode l/Alte PERMIT NO.: 25SP-00049 PERMIT TYPE: ration (Residential) ISSUED DATE: 07/24/2025 EXPIRATION DATE: 01/20/2026 17-117-23- PROJECT ADDRESS: 3842 SUNSET DR, SPRING PARK, MN 55384 PARCEL NO.: 32-0012 OWNER: DAVID D LU & MARY M LU OWNER PHONE: (763) 586-1012 CONTRACTOR: CONTRACTOR PHONE: APPLICANT: David Lu APPLICANT PHONE: (763) 586-1012 DESCRIPTION OF WORK: re -locate one closet wall in one bedroom. re -locate one bathroom wall in the bedroom. relocate vanity CONSTRUCTION TYPE: OCCUPANT LOAD: DATE DATE INSPECTION INSP PASSED COMMENTS INSPECTION INSP PASSED COMMENTS Framing Fire/Draft Stopping Building Final Fire Approval: Date: Engineering Approval: PW Approval: Date: Other To request an inspection: (952) 442-7520 Date: Date: Page 1 of 1 A-rl PARK Project Name: Date: Jurisdiction: ID: Applicant Phone: Jobsite: Code: Reviewed: 07/24/2025 City of Spring Park 25SP-00049 (763) 586-1012 3842 SUNSET DR Approval Status: Construction Type: Applicant Name: Applicant Email: 2020 1309, Minnesota Residential Code Building City of Spring Park 4349 Warren Ave Spring Park, MN 55384 Phone (952) 471-9051 Fax (952) 471-9160 Approved with Comments David Lu ddtotmn@gmail.com The plans and specifications, for the project named above, have been reviewed for substantial compliance with the current Minnesota State Building Code. This review is limited to the submitted scope of work; is based upon the supposition that the data on which the design is based are correct and that the necessary legal authority has been obtained to construct the project. Although every attempt has been made to identify code issues or concerns for proper and necessary change, the project designer(s), the building contractor(s) and the property owner(s) are ultimately responsible for providing complete code compliance and maintaining minimum construction standards for the safeguarding of life or limb, health, public welfare and property while constructing this project. Approval is based on the correction of all noted deficiencies and compliance with all items listed below. Any changes from these documents and/or additional information shall be submitted to the Department of Building Safety for code compliance review and approval. Written response of approval must be on site prior to implementation of such changes. The following information is related to the submitted plans/scope or as general information regarding code compliance. Compliance with the stated requirements will be verified during the construction process. All work shall be inspected. It is the responsibility of the contractor/installer to contact the Department of Building Safety, when ready to schedule an inspection, at (952) 442-7520 during regular business hours. If you have any questions or concerns regarding this plan review, please contact me via telephone at (952) 442-7520 or email at codereview@mnspect.com. Kevin Kamerud Plans Examiner (952) 442-7520 kkamerud@safebuilt.com 3842 SUNSET DR Page 1 PARK Plan Specific Items: Building: Approved with Comments - Kevin Kamerud, kkamerud@safebuilt.com General Requirements: MN Residential Code: City of Spring Park 4349 Warren Ave Spring Park, MN 55384 Phone (952) 471-9051 Fax (952) 471-9160 Bathrooms and water closet compartments without a window compliant with MN Rule 1309.R303.3 are required to have artificial light and mechanical ventilation (MN Rule 1309.R303.3) 2. Bathtub and shower floors and walls above bathtubs with installed shower heads and in shower compartments shall be finished with a nonabsorbent surface. Such wall surfaces shall extend to a height of not less than 6 feet above the floor. (MN Rule 1309.R307.2) 3. Glazing in walls or enclosures containing or facing hot tubs, spas, whirlpools, saunas, steam rooms, bathtubs, showers where the bottom exposed edge if the glazing is less than 60 inches measured vertically above any standing or walking surface shall be considered a hazardous location. This shall apply to single glazing and all panes in multiple glazing. (MN Rule 1309.R308) Exception: 1. Glazing more than 60 inches measured horizontally and in a straight line, from the water's edge of the bathtub, hot tub, spa, whirlpool, or swimming pool or from the edge of a shower, sauna, or steam room. i. Smoke alarms shall be installed in the following locations: (MN Rule 1309.R314.3) a. In each sleeping room b. Outside each separate sleeping area with -in 21' of bedroom doors. c. On each additional story of the dwelling, including basements and habitable attics but not including crawl spaces and uninhabitable attics. In dwellings or dwelling units with split levels and without an intervening door between the adjacent levels, a smoke alarm installed on the upper level shall suffice for the adjacent lower level provided that the lower level is less than one full story below the upper level. d. Smoke alarms shall not be installed within 3' horizontally of a bathroom that contains a tub or shower unless this requirement interferes with other required placements. Smoke alarms shall be interconnected. Combination alarms shall be listed in accordance with UL 217 and UL 2034. (MN Rule 1309.R314.4) ii. When required, Carbon Monoxide alarms shall be installed outside and not more than 10 feet from each separate sleeping area or bedroom. Alarms shall be installed on each level containing sleeping areas or bedrooms. (MN Rules 1309.R315.3) iii. Buildings shall be provided with approved address identification. The address identification shall be legible and placed in a position visible from the street or road fronting the property. These numbers shall contrast with their background. Address numbers shall be Arabic numbers or alphabetical letters. Numbers shall not be spelled out. Numbers shall be a minimum of 4 inches high with a minimum stroke width of 1/2 inch. Where required by the fire code official, address identification shall be provided in additional approved locations to facilitate emergency response. Where access is by means of a private road and the building address cannot be viewed from the public way, a monument, pole, or other sign or means shall be used to identify the structure. Address identification shall be maintained. (MN Rule 1309.R319.1) MN Energy Code: 1. All exhaust, supply, and return air ducts and plenums in conditioned space shall be insulated. 3842 SUNSET DR Page 2 A►" PARK 2. Ducts, air handlers, and filter boxes shall be sealed. (MN Rule 1322.RE403.2.2) City of Spring Park 4349 Warren Ave Spring Park, MN 55384 Phone (952) 471-9051 Fax (952) 471-9160 3. Building framing cavities shall not be used as ducts or plenums. (MN Rule 1309.R403.2.3) 4. Insulation for hot water pipe with a minimum thermal resistance (R-value) of R-3 shall be applied to the following: (MN Rule 1322.RE403.4.2) i. Piping larger than 3/4 -inch nominal diameter. ii. Piping from the water heater to kitchen outlets. iii. Piping located outside the conditioned space. iv. Piping from the water heater to a distribution manifold. v. Piping located under a floor slab. vi. Buried piping. vii. Supply and return piping in recirculation systems other than demand recirculation systems. viii. Piping with run lengths greater than the maximum run lengths for the nominal pipe diameter given in Table R403.4.2. All remaining piping shall be insulated to at least R-3 or meet the run length requirements of Table R403.4.2. 5. A minimum of 75 percent of the lamps in permanently installed lighting fixtures shall be high -efficacy lamps or a minimum of 75 percent of the permanently installed lighting fixtures shall contain only high efficacy lamps. (MN Rule 1322.R404.1) 6. Maximum allowed fenestration U factors, is 0.32 for windows. (MN Rule 1322.Table 402.1.1). Mechanical Code Items: 1. Mechanical ventilation requires a minimum exhaust rate of 50 cfm in toilet rooms and bathrooms. (MN Rule 1346.0403.3.1.1) 2. The air removed by every mechanical exhaust system shall be discharged outdoors at a point where it will not cause a nuisance and not less than the distances specified in (MN Rule 1346.0501.3.1). The air shall be discharged to a location from which it cannot again be readily drawn in by a ventilating system. Air shall not be exhausted into an attic or crawl space and the exhaust system shall be equipped with a backdraft damper at the point of discharge. (MN Rule 1346. 501.3) 3. The termination points of exhaust outlets and ducts discharging to the outdoors shall be located with the following minimum distances: (MN Rule 1346.0501.3.1) I. For all environmental air exhaust: 3 feet from property lines; 3 feet from operable openings into buildings, and 10 feet from mechanical air intakes. 4. Ducts shall be supported at intervals not to exceed 12 feet. Flexible and other factory -made ducts shall be supported in accordance with the manufacturer's instructions. (MN Rule 1346.0603.10) Plumbing Code Items: 1. Fixtures shall be set level and in proper alignment with the reference to adjacent walls. No water closet or bidet shall be set closer than 15 inches from its center to a side wall or obstruction nor closer than 30 inches center to center to a similar fixture. The clear space in front of a water closet or bidet shall not be less than 24 inches. (MN Rule 4714.402.5) 2. Water closets shall have an average consumption not to exceed 1.6 gallons of water per flush (MN Rule 4714.403.2) 3842 SUNSET DR Page 3 .r" PR1NG PARK Laf,e ;Ifinnelonl;a City of Spring Park 4349 Warren Ave Spring Park, MN 55384 Phone (952) 471-9051 Fax (952) 471-9160 3. Shower heads shall have a maximum flow rate of not more than 2.5 gpm at 80 psi. (MN Rule 4714.408.2) 4. Shower and tub -shower controls shall be of the pressure balance, thermostatic, or combination pressure balance/thermostatic mixing type that provides scald and thermal shock protection in accordance with ASSE 1016 or ASME All 12.18.1/CSA B125.1. Handle valves shall be adjusted to deliver a maximum mixed water temperature of 120°F (MN Rule 4714.408.3) 5. Shower compartments, regardless of shape, shall have a minimum finished interior of 1024 square inches and shall also be capable of encompassing a 30-inch circle. (MN Rule 4714.408.6) 6. A temperature limiting device shall be provided on bathtubs and whirlpool tubs to limit the filler temperature to no more than 120° F (MN Rule 4714.409.4) 7. Testing: i. Drain/WasteNent: a. Must hold a uniform 5# psi for 15 minutes. (MN Rule 4714.712.3) b. Gauge increments to be 0.1 psi or less (MN Rule 4714.318.2) c. Test gauges shall have a pressure range not exceeding twice the test pressure applied. (MN Rule 4714.318.5) ii. Water Lines: a. Minimum 50# psi for 15 Minutes (MN Rule 4714.609.4) b. Gauge increments to be 1.0 psi or less (MN Rule 4714.318.3) c. Test gauges shall have a pressure range not exceeding twice the test pressure applied. (MN Rule 4714.318.5) d. Pex manufacturers specifications (MN Rule 4714.609.4) 3842 SUNSET DR Page 4 The field copy of these plans must be kept on -site and made available to inspector during all inspections. To schedule inspections call (952) 442-7520 Please have the permit number and street address ready at the time of the call. Read all attached materials. Everyone performing work to which the code is applicable shall comply with the code. Electrical All electrical must be approved by local Electrical Inspector. For electrical permit inquiries please contact the City of Spring Park Electrical Inspector. Dave Hucky (952) 442-7520 A minimum of R-3 insulation shall be applied to hot water pipe in accordance with the following; * Piping larger than 3/4" nominal diameter. * Piping from the hot water heater to kitchen outlets. * Piping located outside of conditioned space. * Piping from the hot water heater to a distribution manifold. * Piping under a floor slab and any buried piping. * Supply and return piping in hot water circulation systems. * Piping exceeding the maximum lengths given in table R403.4.2. The maximum hot water temperature at Bathtubs and Whirlpool tub fillers not to exceed 120 degrees Fahrenheit, installation of limiting device meeting ASSE 1070 or CSA B125.3 is required. Anti -scald and thermal shock protection device required at shower and tub -shower control valves meeting ASSE 1016 or ASME A112.18/CSA B125.1. Hand -Held showers require back -flow prevention. Internal back -flow prevention devices to comply with ASME Al 12.18.1/CSA B125.1 or have an external back -flow prevention device complying with ASME Al 12.18.3 installed at final inspection. y Existing ceiling, wall, or floor cavities exposed during y construction are required to be filled with insulation. Hardwired and interconnected smoke alarms are required in the following locations: •1 (one) in every bedroom -1 (one) in the area outside every bedroom -At least 1 (one) per floor where no bedrooms exist including basements and habitable attics Existing spaces where no electrical work has taken place may have battery operated smoke alarms that are not interconnected. 1 (one) Carbon Monoxide (CO) alarm is required outside of and within 10-feet of every bedroom or sleeping area. A CO alarm is required on every level that contains a bedroom or sleeping area. CO alarms may be hardwired, plugged into an outlet or battery operated. All required alarms must be installed and operational at time of final building inspection. Reviewed for Code Compliance This review is limited to the submitted scope of work, is based upon the supposition that the plan accurately depicts the intended construction and end -use, that the necessary legal authority has been obtained to construct the project and work is subject to code compliance and field inspection during construction. By: Xevinxamertfd Type of Construction: Not Applicable Date: 7/24/2025 Occupancy Classification: IRC-1 Single Family Dwelling Permit #: 25SP-00049 Code Edition: 2020 MN Residential Code Separate Permits Required For: x Electrical x Mechanical x Plumbing Fireplace Demolition Fire Suppression System Septic O v CO O 9 4.0 Z 41 ao rM Lf) N Z Y L E a O a O C L �L v/♦Q� Q i+ Q CITY OF SPRING PARK BUILDING PERMIT PAGE 1 4349 Warren Avenue Spring Park, MN 55384 ❑ Handout Given Routed to SAFEbuilt Phone: 952-471-9051 Fax: 952-471-9160 ❑ Lead Handout Given 9bW _33 Cry SITE ADDRESS: r , i PID: 1) Was the home constructed before 1978? (YES ❑, continue with line 2, NO continue without completing EPA Section) 2) Will the work disturb ;_>6 sq ft of interior painted surfaces or >_20 sq ft of exterior painted surfaces? (YES4I go to line 4, NO❑line 3) 3) Are there any windows being replaced? (YES ❑, go to line 4, NO%ontinue without completing EPA Section) 4) Has this home been Certified Lead Free? (YES ❑ , you MUST Attach Certification Information, NO Mcomplete line 5) 5) EPA Contractor Certification Number: NAT - PROPERTY OWNER: Address: V_ two-5 ) Ci It ),I State: Zip: ^ Email: p - I'll of rig'o ""MN Conta l Name: ' I L u Phone: 7,03 6 IV CONTRACTOR: Address: City: State: MN Zip: Phone: Fax: Contractor License No: Contact Name: Phone: Email: ARCHITECT: Address: City: State: MN Zip: Phone: Fax: Email: Contact Name: Phone: TYPE OF WORK: ❑New Construction ❑Deck ❑Re -Roof ❑Commercial I&Residential ❑Change of Use ❑Pool ❑Re -Side EST. VALUATION OF WORK ❑Finish Basement ❑Retaining Wall ❑Fence $ �-&V, — ❑Remodel ❑Porch ❑Shed sq ft Square feet: ❑Addition ❑Demolition ❑Window/Door Replacement ❑Garage-Attached/Detach ❑Plumbing -provide detail on Page 2 # being replaced Detailed Description of Work: []Accessory Structure ❑Mechanical-p ovide detail on Page 2 (9Misc Other �440 c` OCl2 CV� OJt-Q c '8�'�1 j'2— ((3s �� aPv�# I�,.�lBC Gl (/ZY)1� signature of this application by the legal property owner or a licensed contractor. as the owner's represontalrvo. rs required and aulharrzes the Zoning Administratorordesignee and the SuIlding Official or designee to enter upon the property to perform needed inspections. Entry may be without prior notice. I hereby acknowledge that I have read this application and state that all Information is true and correct to the best of my knowledge. I further agree that all work performed will be in accordance with approved plans. specifications and conditions and to abide by all ordinances of the ktunicipahty and the laws of the State of Minnesota regarding actions taken pursuant to [his permit I agree to pay all plan review fees even If 1 choose not to proceed with the work. Permit expires when work is not commenced within 160 days from date of permit, or if work - •u�peh� abandoned, or not inspected for 180 days Work beyond the scope or this permit, or work without o Orm l Or Ins eUlon, will be sub oc1 to a parlilty � SIGNATURE OF APPLICANT___ - -DATE:7AL, PRINTED NAME: This is the signature of Owner or ❑Owner' Representative OCCUP. TYPE: CONST. TYPE: CODE: BLDIG SPRINKLED Yes ! No VALUATION: $ Permit Fee: $ Park Dedication: $ Plan Review Fee: $ SAC Charge: $ State Surcharge: $ WAC Charge: $ Site Inspection Fee: $ Sewer Hook -Up: $ S.E.C. Fee: $ Water Hook -Up: $ Investigation Fee / Other Fee: $ Sewer Trunk: $ Copy Charge ($.25 per 8.5x11 page) $ Water Trunk: $ p License Check ($5) / Lead Check ($5) $ Water Meter $ y SUB -TOTAL $ City Fee: $ Plumbing Fee (from Page 2) $ Other: $ v Mechanical Fee (from Page 2) $ TOTAL DUE: $ u- Special Conditions/Required Setbacks: O Building Approval By: DATE: Printed Building Approval By: ❑ License Verification ❑ Lead Verification - Checked By: City Approval By: DATE: Paid: Date: Receipt No. By: N Ri CO O 9 O Z "'-'� .KA PE M RECEIPT City of Spring Park 4349 Warren Ave, Spring Park, MN 55384 (952)471-9051 25SP-00049 I Repair/Remodel/Alteration (Residential) Payment Amount: $289.13 SPRING PARK On Lake 91,linnetonka Receipt Number: 461 July 24, 2025 Transaction Method Payer Cashier Reference Number Check Property Owner Jamie Hoffman 6008 Comments Assessed Fee Items Fee items being paid by this payment Assessed Fee Item On Account Code Assessed Amount Paid Balance Due 07/24/25 State Surcharge $2.85 $2.85 $0.00 07/24/25 Residential Plan Review $112.78 $112.78 $0.00 07/24/25 Residential Building Permit $173.50 $173.50 $0.00 Totals: $289.13 $289.13 Previous Payments $0.00 Remaining Balance Due $0.00 Application Info Property Address Property Owner Property Owner Address Valuation 3842 SUNSET DR DAVID D LU & MARY M LU 5555 MATTERHORN DRIVE $5,695.00 SPRING PARK, MN 55384 NE FRIDLEY, MN 55432 Description of Work re -locate one closet wall in one bedroom. re -locate one bathroom wall in the bedroom. relocate vanity.